Differenze
Queste sono le differenze tra la revisione selezionata e la versione attuale della pagina.
Entrambe le parti precedenti la revisione Revisione precedente Prossima revisione | Revisione precedente Ultima revisione Entrambe le parti successive la revisione | ||
cms:sus-11-016 [02/10/2012 10:46] migliore |
cms:sus-11-016 [03/10/2012 12:21] migliore |
||
---|---|---|---|
Linea 1: | Linea 1: | ||
http://cms.cern.ch/cds/SUS-11-016 | http://cms.cern.ch/cds/SUS-11-016 | ||
+ | |||
+ | Stefano A. | ||
+ | ---------- | ||
+ | |||
+ | Type A: | ||
+ | |||
+ | Abstract: | ||
+ | 1. "up to 4.98 fb-1": we would suggest to write the actual range instead of "up to" (throughout the paper) | ||
+ | |||
+ | 2. "range of mass parameters" : which mass ? | ||
+ | |||
+ | |||
+ | L1-L6: the word "particle" is repeated 3 times in two lines | ||
+ | |||
+ | L5: "one theoretical model ..." This is coming out of the blue, we should at least say (in one sentence) why this particular one is used in most CMS analyses. | ||
+ | |||
+ | L5 : "in most CMS analyses " -> In most of the analyses performed by the CMS collaboration (or similar rephrasing) | ||
+ | |||
+ | L7 : principal -> principle (or at least, this seems to be the intended meaning) or remove the word and commas. | ||
+ | |||
+ | L7/9 : repetition of the word "particle" | ||
+ | |||
+ | L13-14 : "For each SimplM, values of Axepsilon can be calculated to translate a number of signal events into a cross section " . This needs rephrasing, e.g. "can be calculated to measure a cross section given the number of observed signal candidates". But it is not clear at this point if it _can_ be calculated or if actually did it. | ||
+ | |||
+ | L15/16: We would suggest: "an upper limit on the xs times the br ($[\sigma \times BF]_{UL}$)", then remove ($[\sigma \times BF]$) at the end of the sentence. The definition in symbols without the UL is not used in the rest of the paper if we are not mistaken. | ||
+ | |||
+ | |||
+ | L113 : "denoted the " -> denoted as the | ||
+ | |||
Nicolo` | Nicolo` | ||
Linea 66: | Linea 95: | ||
What's about "is fully defined specifying the masses and the production and decay sequence of a set of new particles" | What's about "is fully defined specifying the masses and the production and decay sequence of a set of new particles" | ||
- | L35: "built around" -> I am not a native English speaker but it sound a bit strange to me being almost CMS "contained" | + | L35: "built around" -> I am not a native English speaker but it sounds a bit strange to me being almost CMS "contained" |
within the solenoid | within the solenoid | ||
Linea 75: | Linea 104: | ||
L.165: "SUSY expressions" -> "SUSY predictions" | L.165: "SUSY expressions" -> "SUSY predictions" | ||
- | L.170: since it is used later, one should probably emphasize even more what is the "benchmark" | + | L.170: since it is used later as key-ingredient for extracting the limits, one should probably emphasize even more what is the "benchmark" |
- | => Then [sigma x BF]_UL is compared to the SUSY benchmark cross section ..." | + | => "Then [sigma x BF]_UL is compared to the SUSY benchmark cross section ..." |
L.181: "chargino mass" -> "heavier (or intermediate?) neutralino mass" | L.181: "chargino mass" -> "heavier (or intermediate?) neutralino mass" | ||
- | For clarity, should be underlined that this corresponds to x=1/2 of L.116, as in the caption of Fig.1? | + | For clarity, one should underline that this corresponds to x=1/2 of L.116, as in the caption of Fig.1. |
- | L.187: "different mass parameters" -> for clarity one should probably write explicitly "different values of the masses of the gluino and of the lightest neutralino" | + | L.187: "different mass parameters" -> again for clarity one should probably write explicitly "different values of the masses of the gluino and of the lightest neutralino" |
L.198 (and Fig.1): | L.198 (and Fig.1): | ||
- | While it is clear how efficiency*acceptance is extracted it is less clear why the figures on the right do not show the same pattern (e.g. isolines) of those on the left but with a different scale. | + | While it is clear how efficiency*acceptance is extracted it is less clear why the figures on the right do not show the same pattern (e.g. isolines) of those on the left just with a different scale. |
- | More specifically: the text mentions "the predicted background". Is the number of predicted background events the same for all the points in the (m(~g),m(LSP)) plane and then the difference arises only when including it in the CLs calculation? Or is the selection of the events different in different regions of the (m(~g),m(LSP)) plane, so the number of selected events changes as well? | + | More specifically: the text mentions "the predicted background". Is the number of predicted background events the same for all the points in the (m(~g),m(LSP)) plane and the difference in the isoline patterns between left and right plots arises only when including it in the CLs calculation? Or is the selection of the events different in different regions of the (m(~g),m(LSP)) plane, so the number of selected events changes as well? |
L.214: remove "The limits are thus subject to statistical fluctuations" (as everything...) | L.214: remove "The limits are thus subject to statistical fluctuations" (as everything...) | ||
- | Fig.1 In the top header of each plot: Why m(~q)>>m(~g) and not the opposite? | + | Fig.1 caption "chargino" -> "neutralino" |
+ | |||
+ | I have also two conceptual questions about these plots: | ||
+ | |||
+ | 1) Does LSP coincide with N_0^1 for all the points of the plots? | ||
+ | |||
+ | 2) The fine dashed lines diagonal seem to indicate a kinematic limit, e.g. m(LSP)<m(~g), which is probably wrong for the topology analyzed as for the cascade ~g->N_0^2->N_0^1 is m(LSP)<m(~g)-m(N_0^2) | ||
+ | Also the fact that there is a constant offset between the dashed line and the edge of the "color" region is not intuitive as I would expect a constant offset for a constant value of m(N_0^2), specifically 200 GeV. | ||
+ | Could you elaborate a bit on it? | ||
- | caption "chargino" -> "neutralino" | ||