Differenze
Queste sono le differenze tra la revisione selezionata e la versione attuale della pagina.
| Entrambe le parti precedenti la revisione Revisione precedente Prossima revisione | Revisione precedente | ||
|
vlsi:personalpages:cenna:links [21/03/2015 09:50] cenna |
vlsi:personalpages:cenna:links [23/11/2015 14:33] (versione attuale) cenna |
||
|---|---|---|---|
| Linea 1: | Linea 1: | ||
| - | Here is a list of laboratory instruments and common issues in remote control | + | Links |
| - | **Oscilloscope LeCroy 625Zi**\\ | ||
| - | BW: 2GHz\\ | ||
| - | OS: Windows 7\\ | ||
| - | Connection types: USB-GPIB, Ethernet\\ | ||
| - | * USB: be sure to enable remote control from oscilloscope menu Utilities > Remote\\ | ||
| - | * Ethernet: \\ | ||
| - | Team Viewer: the instrument has TW installed. Install TW on your pc to control the oscilloscope from your machine\\ | ||
| - | Labview driver: [[http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=07C0AC709BD14C10E0440003BA7CCD71]] | ||
| - | **Oscilloscope LeCroy 6100A**\\ | + | __[[http://gen.lib.rus.ec/|Library Genesis]]__ |
| - | BW: 1GHz\\ | + | |
| - | OS: Windows XP\\ | + | |
| - | Connection types: USB-GPIB, Ethernet\\ | + | |
| - | Note: this device needs a non standard GPIB connector, micro-d25 to GPIB converter is needed (rare)\\ | + | |
| - | Labview driver: [[http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=07C0AC709BD14C10E0440003BA7CCD71]] | + | |
| - | + | ||
| - | **Picosecond laser**\\ | + | |
| - | Pulsed laser diode (3B class)\\ | + | |
| - | Power: 1200 mW\\ | + | |
| - | Wavelengths: 1064 nm, 405 nm\\ | + | |
| - | Connection types: serial (RS232, USB-serial)\\ | + | |
| - | Note: needs RS232 male-male cable (!), in case you don't have one, use USB connection. The connection can be displayed from Control Panel > System > Devices on your pc as UART (USB emulating serial) e.g. on COM3 port, then configure the serial connection as following:\\ | + | |
| - | * Baud rate: 19200 | + | |
| - | * Bits: 8 | + | |
| - | * Stop bits: 1 | + | |
| - | * End of command: carrier return \r (the instrument recognize the command only after carrier return) | + | |
| - | * Command list: state > display system status\\ | + | |
| - | debug > display additional information\\ | + | |
| - | ld=(0 disabled, 1 enabled) > enable/disable laser\\ | + | |
| - | ld? > ask laser if enabled/disabled\\ | + | |
| - | tune=(0 max, 1000 min) > set laser attenuation\\ | + | |
| - | tune? > display laser attenuation\\ | + | |
| - | te=(0 falling, 1 rising) > set trigger edge\\ | + | |
| - | te? > display trigger edge\\ | + | |
| - | + | ||
| - | Basic vi example to communicate with laser: {{:vlsi:personalpages:cenna:drivers:provacomandi.zip|}} | + | |
| - | Labview drivers: | + | |